Skip to content Skip to side menu

Tied to the Sky

Wind Ranges for Kites - What to think!

Wind Ranges for Kites - What to think!

Andrea of Great Canadian Kite Company flying her Revolution kite

I remember as a kid trying to fly kites that you had to run like mad just to keep them aloft. It made for a very frustrating experience. One exception from my childhood was a delta shaped black plastic kite  - the one that you affixed adhesive eyes too. These fiery eyes made it look pretty cool, and you know, it flew pretty well! As fun as that kite was, being made of plastic it didn't last very long!

When we started the Great Canadian Kite Company (read our story here) we wanted to make sure that we sold a quality product that flew well and was built to be durable by quality kite standards. As such, the kites we have chosen are from reputable manufacturers with proven designs that fly in the stated conditions.

But even then... what does a wind range really mean? A wind range is provided to communicate the range of wind speed that the kite will fly in. So a range of 10 - 40 kph means that the kite is capable of flying in winds as low as 10 Kph to an upper limit of 40 kph.

The upper range can be a little more flexible if just flying the kite is the priority. When kites fly in winds above the range, they will often become much faster, harder to control, pull too hard and become difficult to trick. Too much wind will rip stitches and fabric, or break framing and line. It also can increase the potential for damage with hard crashes.

In higher winds you can add wind brakes or add tails, and this will often raise the upper limit.

Nexus Kite by Prism KitesSometimes, especially with stunt kites (low wind or Indoor) you see a lower wind range of zero or 5 or 8 or 10 kph. Low wind kite flying is an art as much as it is a science, and many manufacturers when establishing the lower end of the wind range have folks testing it who are really good pilots!

So can the kites fly at those low ranges? You bet! Can anybody fly them in the low range - with some practice you can learn to keep your kite aloft at the lowest wind ranges.

As kite professionals, we are here to offer you experienced recommendation on the kinds of kites and kite accessories that will get you in the air with the goal of providing the best kite flying experience we can!

Great Canadian Kite Company also have some Resources for the Kite Flyer:

Read more →

Extended leaders on B-Series Rev Kite Handles

Extended leaders on B-Series Rev Kite Handles

Revolution Kite - extended leadersIf you haven't tried a Revolution kite - you really have to take the plunge!   Revolution kites are one of the most dynamically expressive and interactive sport wing kites you can enjoy today!   If you have, you know the thrill first hand and are at work studying the master flyers and tuning your kites and accessories for your personal flying preferences.

You also know that Great Canadian Kite Company is hands down one of the best Canadian sources for Rev kites and accessories including lines,  custom handles, frames and replacement parts - all at competitive prices with great personalized service!

 

B-Series flyers will recognize the extended leaders on their handles but for those of us flying 1.5's and other Rev kite packages the extended leaders may be new to us.

The extended leaders replace the top leaders on your flying handles.   They are almost 2 times longer and have a series of knots along the length of it.  These make for a series of  points to connect your flying line to the handles.  Each point alters the aspect of the wing (kite) in effect adding or reducing brake.  This ideally helps tune our kites not only for the conditions but also our flying preferences and abilities.

We had time to spend with the Master himself, Jon Baressi and among other things he shared his tuning tip for new fliers on B-leaders.  

"Start at the end knot, try to launch, bring in one knot at a time until you can launch. Every couple months, do the same approach again and as they get better, their "happy knot" will be further and further out."

It is a very simple and practical approach and with practice your skills will improve Revolution kites - extended leaders B-Seriesdramatically.   When we teach people to fly Revolution kites we like to use handles with extended leaders because we find it increase flyer success much faster.   The sooner our students experience success with their kites, the sooner they're tearing up the sky - with a big grin on their face!

If you have a set of handles with the normal leaders, not to worry.  We stock extended leaders here at the Great Canadian Kite Company.   The are so easy to install!  You may want to consider including those new leaders with a new Revolution kite as well!

Read more →

Prism Isotope & Mantis Kite : Tech Tips


Prism Kites has had reports from Isotope and Mantis owners that they were having trouble getting them to fly stable without wandering back and forth. It took a while to diagnose the problem because whenever we'd get a kite back to check it would fly perfectly- frustrating! After much detective work we finally figured it out, and kites in production from summer 2015 onward were tweaked to address the problem. Here's what you need to know- please pass the word if you hear from someone having trouble:


Mantis: The Mantis flies nice and stable as long as the Velcro at the end of the spine is tightened enough to put a downward bow in the spine when it's assembled. If the Velcro is loose and the spine has no bow it will reduce stability, especially in stronger winds. That info is in the instructions for the Mantis, but there is now a printed tag sewn right onto the Velcro to remind customers as they assemble the kite.

Isotope: The early Isotopes had a similar issue with spine tension, but with the opposite result- of all the rotten luck!  For the Isotope, the kite can be unstable if the spines are tensioned very tightly with the tail Velcros during assembly. This flattens the sail too much for stable flight and the kite can wander back and forth in stronger winds. To fix it in production last summer we shortened the Isotope spines slightly so it would be impossible for a customer to pull the Velcro too tight.

______________________________

Thanks to Prism Kites for this information.  These issues are related to kites in the first run of production, early last Spring.  Great Canadian Kite Company didn't receive kites from this manufacturing lot but we have received customer service calls from those who purchased this lot from other kite retailers.  We have provided this info and sure it will help you really enjoy your kites!

Read more →